- Free inspections
- Owner-performed inspections
- Exposed-fastener and standing-seam systems
- Metal-roof repairs and re-screws
- Licensed and insured
- License # CCC1335406
A More Personal Metal-Roofing Experience
Owner Involvement
Deston generally inspects the roof, explains the estimate, checks the completed work, and remains available to the homeowner.
Honest System Comparison
Destination Roofing explains when exposed-fastener metal is the practical choice and when standing seam may justify the additional cost.
Repair Before Replacement
A leaking metal roof may qualify for repair or a complete re-screw when the panels remain sound and corrosion is not widespread.
Competitive Pricing
Lean overhead helps Destination Roofing offer competitive pricing without cutting important roofing-system components from the proposal.
Metal-Roofing Systems We Install
Destination Roofing works with a range of metal-roofing systems for Florida homes and buildings.
Exposed-fastener systems
- Tough Rib
- Ultra Rib
- 5V Crimp
- PBR panels where appropriate
Concealed-fastener systems
- Snap-lock standing seam with screw strip
- Snap-lock standing seam with clips
- Mechanically seamed standing seam
The right system depends on roof design, roof pitch, budget, desired appearance, building type, panel length, engineering requirements, long-term maintenance expectations, and any HOA or architectural requirements.
Exposed-Fastener Metal Roofing
Exposed-fastener roofing is the most common metal system selected by Destination Roofing customers because it provides the appearance and durability of metal at a substantially lower initial cost than standing seam.
- Fasteners pass through the panel and attach it to the roof structure.
- Proper screw placement and washer compression matter.
- Screws must not be driven too loose or over-tightened.
- Fasteners and sealants require periodic inspection as the roof ages.
- Long-life ZAC screws are used where appropriate.
- Wood-to-metal or metal-to-metal fasteners are selected according to the roof assembly.
- Manufacturer-compatible, color-matched sealant is used at appropriate details.
Gauge: For residential exposed-fastener metal roofing, Destination Roofing generally uses 26-gauge metal or heavier, depending on the approved panel system, design, and project requirements.
Most common panel: Tough Rib or Ultra Rib is our most commonly installed exposed-fastener profile. If you would like to see it on your own roof, request a free inspection or view recent local metal projects below.
Standing-Seam Metal Roofing
Standing seam is a premium concealed-fastener system. The primary panel fasteners are hidden beneath the seams rather than exposed directly to weather.
Available systems may include:
- Snap-lock panels with a screw strip
- Snap-lock panels installed with clips
- Mechanically seamed panels
Destination Roofing's most common standing-seam configuration is snap lock with a concealed screw strip, depending on the roof design and manufacturer requirements.
Gauge: Standing-seam residential systems are generally installed using approximately 24-gauge metal, depending on the project, engineering, panel system, and manufacturer.
Benefits
- Concealed primary fasteners
- Cleaner appearance
- Premium system design
- Fewer exposed fastener washers requiring long-term maintenance
- Multiple panel and seam options
Tradeoffs
- Significantly higher initial cost
- More detailed fabrication and installation
- Roof geometry can materially affect price
- Not every homeowner needs the premium system
Exposed Fastener or Standing Seam: Which Is Better for Your Home?
| Consideration | Exposed Fastener | Standing Seam |
|---|---|---|
| Initial cost | Lower | Substantially higher |
| Fastener visibility | Visible screws through the panel | Concealed under the seam |
| Maintenance considerations | Periodic screw, washer, and sealant inspection | Fewer exposed fasteners; details still require inspection |
| Appearance | Traditional ribbed metal look | Cleaner, premium seam profile |
| Panel attachment | Screws directly through panel into substrate | Snap-lock with screw strip, snap-lock with clips, or mechanically seamed |
| Typical homeowner | Wants a metal roof at a reasonable price | Wants a premium concealed-fastener upgrade |
| Roof complexity | Works well on most roof designs | Complex geometry can materially affect price |
| Upgrade level | Practical metal system | Premium metal system |
Exposed-fastener metal is often the practical choice when a homeowner wants a metal roof without the premium price of standing seam. Standing seam may be the better fit when concealed fasteners, appearance, and a premium roof system are higher priorities. Destination Roofing explains both options rather than assuming the highest-priced system is automatically best.
How Destination Roofing Installs Metal Roofs
- Existing roofing conditions are inspected before installation.
- High-temperature peel-and-stick underlayment is installed beneath metal roofing.
- Panel type and gauge are selected according to the roof and approved system.
- Panels are measured and installed to maintain straight, consistent lines.
- Fasteners are selected for the actual substrate.
- Exposed screws are checked for proper placement and compression.
- Manufacturer-compatible sealant is used at appropriate details.
- New metal trim and flashing are integrated with the panel system.
- Penetrations, transitions, eaves, gables, valleys, ridges, and walls are detailed according to the roof design.
- Deston personally checks overall workmanship and confirms that fasteners and important details were not missed.
- Final photographs are taken.
The Details Beneath and Around a Metal Roof
High-temperature peel-and-stick underlayment
Destination Roofing installs high-temperature peel-and-stick underlayment beneath metal roofing. The exact brand may vary based on availability, compatibility, and project requirements.
Flashing and trim
New metal trim and flashing are installed as integrated parts of the metal-roofing system, including:
- Eaves
- Gables
- Ridges
- Hips
- Valleys
- Sidewalls
- Headwalls
- Roof transitions
Pipe and roof penetrations
Penetrations require compatible boots, flashing, and sealant. Electrical risers may use neoprene zipper boots where appropriate. Larger chimneys may require a cricket to divert water; the roof and applicable requirements must be evaluated before deciding.
Metal-Roof Repair
Common problems Destination Roofing repairs on existing metal roofs include:
- Backing-out screws
- Failed rubber washers
- Loose fasteners
- Failed sealant
- Leaks around penetrations
- Damaged trim
- Ridge or transition leaks
- Limited panel damage
- Improper previous repairs
- Rust beginning in isolated locations
A limited problem may be repairable when the surrounding panels remain structurally sound. Learn more on our roof-repair page.
Complete Metal-Roof Re-Screw Service
A leaking exposed-fastener metal roof does not always require full replacement. When the panels remain structurally sound and widespread rust is not present, a complete re-screw may restore the fastening system and extend the roof's useful service.
- Inspect panel and fastener condition.
- Identify corrosion, panel damage, and failed details.
- Remove the existing screws.
- Install wider-diameter long-life ZAC screws so they can properly bite into the existing fastener openings.
- Use wood-to-metal or metal-to-metal fasteners as appropriate.
- Reseal penetrations and vulnerable metal details.
- Inspect the roof to confirm fasteners were installed and no major details were missed.
- Take final photographs.
Destination Roofing does not recommend a re-screw when panels are widely rusted, severely deteriorated, damaged beyond repair, or unable to reliably hold new fasteners.
Does Your Metal Roof Need Repair, Re-Screwing, or Replacement?
Limited repair may make sense when:
- · The leak is isolated
- · Only a few fasteners or details failed
- · Panels remain sound
- · Rust is limited
- · The problem can be clearly identified
A complete re-screw may make sense when:
- · Fastener problems are widespread
- · Panels remain structurally serviceable
- · Existing holes can accept wider-diameter replacement screws
- · Sealant and penetration maintenance are also needed
- · Corrosion is not widespread
Replacement may make more sense when:
- · Panels are widely rusted
- · Metal is severely deteriorated
- · Fasteners no longer hold reliably
- · Leaks occur across multiple areas
- · Previous repairs repeatedly fail
- · The underlying roof system needs broader correction
- · The owner wants to upgrade to a different metal system
Destination Roofing has talked homeowners out of full metal-roof replacement when a complete re-screw was the more reasonable option. When broader deterioration is present, see roof replacement.
Can a Metal Roof Be Installed Over Existing Shingles?
Whether metal can be installed over an existing roof depends on the existing layers, roof deck, applicable code, manufacturer requirements, roof design, ventilation, moisture conditions, and approved installation method.
Tear-off offers several advantages:
- Exposes the roof deck
- Allows damaged decking to be identified
- Removes hidden deterioration
- Allows the new underlayment and roof system to begin from a known surface
Installation over an existing roof should not be recommended automatically simply because it reduces tear-off labor.
What Affects Metal-Roofing Cost in Citrus County?
- Total roof surface area
- Exposed fastener versus standing seam
- Panel profile
- Metal gauge
- Roof pitch
- Number of hips, valleys, ridges, and transitions
- Roof height and access
- Panel lengths
- Existing roofing layers
- Tear-off requirements
- Damaged decking
- Chimneys and crickets
- Skylights
- Electrical risers
- Ventilation
- Complex flashing
- Attached lanais or additions
- Material color and finish
- Engineering or project requirements
- Delivery and fabrication requirements
Exposed-fastener metal is substantially less expensive than standing seam. Destination Roofing explains both systems and provides a written estimate based on the actual roof rather than publishing a misleading one-price-fits-all number.
Our Metal-Roofing Process
- Initial contact. Liz or Deston receives the request and creates a work order in AccuLynx.
- Free inspection. Deston generally inspects the roof personally.
- System recommendation. The homeowner receives an explanation of exposed fastener, standing seam, repair, re-screw, or replacement options.
- Written estimate. The estimate is commonly prepared and discussed at the property.
- Material and color selection. The homeowner selects the approved panel profile, gauge, color, and optional upgrades.
- Permits, tear-off, and installation. The office handles permit and inspection scheduling. The existing roof is prepared according to the approved scope, and the metal system is installed.
- Owner review and cleanup. Deston checks workmanship, fasteners, important details, and cleanup. Final photographs are taken.
Protecting Your Property During Metal-Roof Installation
- Landscaping is protected with tarps where appropriate.
- Tarps or plywood may be used around newer or higher-quality driveways.
- Air-conditioning equipment may be shielded using plywood or another suitable barrier.
- Pool areas affected by debris are cleaned.
- Removed fasteners and metal debris are carefully collected.
- Magnetic nail bars are used repeatedly when appropriate.
- Final cleanup and workmanship are personally reviewed by Deston.
Recent Metal-Roofing Projects in Citrus County
Lecanto Metal Roof Before and After
Standing Seam Galvalume Roof in Lecanto, FL
Metal-Roof Workmanship Warranty
Standard full-roof installations generally receive a 15-year Destination Roofing workmanship warranty. The workmanship warranty generally covers the labor and material required to correct leaks caused by Destination Roofing's improper installation, subject to the written contract, exclusions, and warranty terms.
Repair and re-screw warranty terms follow the written proposal and warranty for that specific scope of work.
If a legitimate installation-related problem develops, Destination Roofing's approach is to inspect the issue and honor the written warranty rather than automatically search for an excuse to avoid responsibility.
Metal Roofing for Citrus County Weather
- Florida sun and heat place demands on coatings, sealants, and underlayment.
- Heavy rain tests valleys, walls, penetrations, and roof transitions.
- High winds place stress on panel edges, fasteners, seams, and trim.
- Exposed-fastener roofs require long-term attention to washers and screws.
- Standing-seam systems conceal the main panel fasteners but still require proper flashing and detailing.
- Humidity and trapped moisture make correct underlayment and ventilation important.
- Low-slope additions require systems and drainage appropriate for the roof pitch — see flat roofing.
- Roof-to-wall connections can be evaluated for third-nail wind-mitigation improvements during a larger project.
Related resources: soffit and fascia, storm-damage roof repair, commercial roofing, and shingle roofing.
What Homeowners Say About Destination Roofing
"Thanks for your help and knowledge in my roof situation. He came out on a holiday to fix my leak, it was an easy fix he didn't even charge me and that says enough about this business. Thank you! Highly recommend."
"Destination was one of three roofing companies called for a small roof leak. First guy said we needed plywood etc. Destin was honest and fixed the actual problem."
"Destin came out after other roofing companies came out and found the leak that no one else could find. He is super professional."
Metal-Roofing Guidance From an Experienced Local Roofer
This page is reviewed by Deston Judy, owner and licensed roofing contractor for Destination Roofing Inc. Deston began working in roofing at age 15 and personally performs many inspections, explains metal-roofing options, reviews estimates, and checks completed work.
- Florida roofing license # CCC1335406
- More than 100 roofs completed by Destination Roofing
- Approximately 15 years rooted in Citrus County
More about Deston and Destination Roofing →
Metal-Roofing Questions
Is standing seam better than exposed-fastener metal?
What metal gauge does Destination Roofing use?
What is installed beneath a metal roof?
Can a leaking metal roof be repaired?
What is a complete metal-roof re-screw?
When is a re-screw not recommended?
Does a metal roof require maintenance?
Can metal be installed over shingles?
How much more does standing seam cost?
Which exposed-fastener profile do you install most often?
Which metal suppliers do you use?
Does metal roofing help during Florida storms?
What workmanship warranty comes with a new metal roof?
Who performs the inspection?
Metal Roofing Throughout Citrus County
We install and service metal roofs across Citrus County, including Beverly Hills, Inverness, Crystal River, Homosassa, Lecanto, Hernando, Floral City, Citrus Springs, Dunnellon, and Spring Hill. Browse all service areas and roofing services, or request a free roof inspection.
Get an Honest Metal-Roofing Recommendation
Destination Roofing will inspect the actual roof and explain whether repair, re-screwing, exposed-fastener replacement, or standing seam makes the most sense.